Proxim AP-700 User's Guide Page 20
- Page / 231
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Initialization AP-700 User Guide
Hardware Installation
20
2. Slide the hinging end of the security cover into the hole on the rear panel of the unit to the left of the connectors. Once
in place, pivot the right side of the cover to bring it close to the rear panel of the unit.
3. Use the two attached screws to fasten the security cover onto the rear panel of the unit.
Mount the AP-700
Proxim recommends that you have a site survey professionally conducted to determine the best location for the AP. For
professional site surveyors, Ekahau Site Survey software is included in the Xtras folder on the Installation CD-ROM.
Note that the AP-700 has been certified under UL Standard 2043 and can be installed in the plenum. In an office building,
plenum is the space between the structural ceiling and the tile ceiling that is provided to help air circulate. Many
companies also use the plenum to house communication equipment and cables. These products and cables must
comply with certain safety requirements, such as Underwriter Labs (UL) Standard 2043: “Standard for Fire Test for Heat
and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air-Handling Spaces”.
NOTE: When installed in a plenum, the AP must use PoE.
Once you have chosen a final location for your unit, the following are the mounting options are available:
• Wall Mounting
• Ceiling Mounting
Wall Mounting
Follow these steps to mount the unit on a wall:
1. If the unit’s power supply is plugged in, unplug it.
2. Put the mounting plate up to the wall so that the embossed letter “L” is on top (see figure). If the plate is correctly
oriented, the circular tab that is vertically aligned with the square hole should be on top.
3. Fasten the mounting plate with two screws through the circular holes of the plate. Depending on the type of wall, you
may need to use the two fasteners provided.
4. Holding the unit so that the connectors on the rear are facing left, align the two holes on the bottom of the unit with the
two tabs on the mounting plate. Press the unit down so it is flush with the plate.
5. Carefully slide the unit to the right until the tabs snap securely onto the narrow holes of the unit. If the unit is mounted
correctly, no portion of the mounting plate should protrude from any of the sides of the unit.
- ORiNOCO AP-700 1
- Copyright 2
- Trademarks 2
- OpenSSL License Note 2
- Contents 3
- Introduction 8
- HTTP/HTTPS Interface 9
- Command Line Interface 9
- SNMP Management 10
- SSH (Secure Shell) Management 10
- AP-700 Hardware Description 13
- Power-over-Ethernet (PoE) 14
- Antennas 14
- Prerequisites 16
- System Requirements 16
- Product Package 17
- Hardware Installation 18
- Mount the AP-700 20
- Power On the Unit 21
- 23
- Initialization 25
- Logging In 27
- Using the Setup Wizard 28
- Installing the Software 30
- System Status 33
- Advanced Configuration 34
- Dynamic DNS Support 37
- IP Configuration 38
- DHCP Server 39
- DHCP Relay Agent 41
- Link Integrity 42
- Ethernet 56
- Management 58
- IP Access Table 59
- Services 59
- Filtering 70
- Static MAC 71
- Advanced 74
- TCP/UDP Port 76
- Rogue Scan 86
- Figure 4-35 Rogue Scan Screen 89
- Spanning Tree 90
- Storm Threshold 91
- Intra BSS 92
- Packet Forwarding 92
- Priority Mapping 95
- Radius Profiles 99
- Configuring Radius Profiles 100
- RADIUS Accounting 103
- SSID/VLAN/Security 105
- Management VLAN 107
- Security Profile 108
- MAC Access 115
- Wireless 116
- Monitoring 122
- IP/ARP Table 125
- Learn Table 126
- Monitoring AP-700 User Guide 127
- Interfaces 129
- Station Statistics 132
- Mesh Statistics 134
- Commands 135
- TFTP File Transfer Guidelines 136
- HTTP File Transfer Guidelines 136
- Update AP 137
- Update AP via HTTP 138
- Retrieve File 140
- Retrieve File via HTTP 141
- Commands AP-700 User Guide 142
- Help Link 145
- Troubleshooting 146
- Symptoms and Solutions 147
- Client Connection Problems 149
- VLAN Operation Issues 149
- Power-Over-Ethernet (PoE) 150
- Recovery Procedures 151
- set ipaddrtype static 155
- reboot 0 155
- Related Applications 156
- Command Line Interface (CLI) 157
- General Notes 158
- CLI Error Messages 159
- Bootloader CLI 160
- CLI Command Types 162
- Parameter Control Commands 166
- Using Tables and Strings 170
- Log into the AP using Telnet 172
- Other Network Settings 178
- (Mbits/sec)> 180
- CLI Monitoring Parameters 187
- Parameter Tables 188
- System Parameters 190
- Network Parameters 192
- Interface Parameters 196
- Management Parameters 202
- Filtering Parameters 205
- Alarms Parameters 207
- Bridge Parameters 209
- RADIUS Parameters 211
- Security Parameters 212
- VLAN/SSID Parameters 214
- Other Parameters 214
- CLI Batch File 218
- Reboot Behavior 219
- ASCII Character Chart 220
- Specifications 221
- Advanced Bridging Functions 222
- Security Functions 223
- Network Functions 223
- Hardware Specifications 224
- Available Channels 225
- Support Options 229
- Statement of Warranty 230
- Other Information 231
© 2020, manymanuals.com. All rights reserved. | 0.364 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals