Proxim AP-700 User's Guide Page 42
- Page / 231
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration AP-700 User Guide
Network
42
DHCP Server IP Address Table
The AP supports the configuration of a maximum of 10 server settings in the DHCP Relay Agents server table. At least
one server must be configured to enable DHCP Relay.
To add entries to the table of DHCP Relay Agents, click Add in the DHCP Server IP Address Table; to edit existing
entries, click Edit. The following window is displayed.
Figure 4-6 DHCP Server IP Address Table - Edit Entries
To add an entry, enter the IP Address of the DHCP Server and a comment (optional), and click OK.
To edit an entry, make changes to the appropriate entry. Enable or disable the entry by choosing Enable or Disable from
the Status drop-down menu, and click OK.
Link Integrity
The Link Integrity feature checks the link between the AP and any nodes on the backbone. These nodes are listed by IP
address in the Link Integrity IP Address Table. The AP periodically pings the nodes listed within the table. If the AP loses
network connectivity (that is, the ping attempts fail), the AP disables its wireless interface(s). Note that this feature does
not affect WDS links (if WDS links are configured and enabled).
You can configure and view the following parameters within the Link Integrity Configuration screen:
• Enable Link Integrity: Place a check mark in the box provided to enable Link Integrity.
• Poll Interval (milliseconds): The interval between link integrity checks. Range is 500-15000 ms in increments of
500 ms; default is 500 ms.
• Poll Retransmissions: The number of times a poll should be retransmitted before the link is considered down.
Range is 0 to 255; default is 5.
• Target IP Address Entry: This entry specifies the IP address of a host on the network that the AP will periodically poll
to confirm connectivity. The table can hold up to five entries. By default, all five entries are set to 0.0.0.0. Click Edit to
update one or more entries. Each entry contains the following field:
– Target IP Address
– Comment (optional)
– Status: Set this field to Enable to specify that the Access Point should poll this device. You can also disable an
entry by changing this field’s value to Disable.
- ORiNOCO AP-700 1
- Copyright 2
- Trademarks 2
- OpenSSL License Note 2
- Contents 3
- Introduction 8
- HTTP/HTTPS Interface 9
- Command Line Interface 9
- SNMP Management 10
- SSH (Secure Shell) Management 10
- AP-700 Hardware Description 13
- Power-over-Ethernet (PoE) 14
- Antennas 14
- Prerequisites 16
- System Requirements 16
- Product Package 17
- Hardware Installation 18
- Mount the AP-700 20
- Power On the Unit 21
- 23
- Initialization 25
- Logging In 27
- Using the Setup Wizard 28
- Installing the Software 30
- System Status 33
- Advanced Configuration 34
- Dynamic DNS Support 37
- IP Configuration 38
- DHCP Server 39
- DHCP Relay Agent 41
- Link Integrity 42
- Ethernet 56
- Management 58
- IP Access Table 59
- Services 59
- Filtering 70
- Static MAC 71
- Advanced 74
- TCP/UDP Port 76
- Rogue Scan 86
- Figure 4-35 Rogue Scan Screen 89
- Spanning Tree 90
- Storm Threshold 91
- Intra BSS 92
- Packet Forwarding 92
- Priority Mapping 95
- Radius Profiles 99
- Configuring Radius Profiles 100
- RADIUS Accounting 103
- SSID/VLAN/Security 105
- Management VLAN 107
- Security Profile 108
- MAC Access 115
- Wireless 116
- Monitoring 122
- IP/ARP Table 125
- Learn Table 126
- Monitoring AP-700 User Guide 127
- Interfaces 129
- Station Statistics 132
- Mesh Statistics 134
- Commands 135
- TFTP File Transfer Guidelines 136
- HTTP File Transfer Guidelines 136
- Update AP 137
- Update AP via HTTP 138
- Retrieve File 140
- Retrieve File via HTTP 141
- Commands AP-700 User Guide 142
- Help Link 145
- Troubleshooting 146
- Symptoms and Solutions 147
- Client Connection Problems 149
- VLAN Operation Issues 149
- Power-Over-Ethernet (PoE) 150
- Recovery Procedures 151
- set ipaddrtype static 155
- reboot 0 155
- Related Applications 156
- Command Line Interface (CLI) 157
- General Notes 158
- CLI Error Messages 159
- Bootloader CLI 160
- CLI Command Types 162
- Parameter Control Commands 166
- Using Tables and Strings 170
- Log into the AP using Telnet 172
- Other Network Settings 178
- (Mbits/sec)> 180
- CLI Monitoring Parameters 187
- Parameter Tables 188
- System Parameters 190
- Network Parameters 192
- Interface Parameters 196
- Management Parameters 202
- Filtering Parameters 205
- Alarms Parameters 207
- Bridge Parameters 209
- RADIUS Parameters 211
- Security Parameters 212
- VLAN/SSID Parameters 214
- Other Parameters 214
- CLI Batch File 218
- Reboot Behavior 219
- ASCII Character Chart 220
- Specifications 221
- Advanced Bridging Functions 222
- Security Functions 223
- Network Functions 223
- Hardware Specifications 224
- Available Channels 225
- Support Options 229
- Statement of Warranty 230
- Other Information 231
© 2020, manymanuals.com. All rights reserved. | 1.298 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals