Proxim ORiNOCO User's Guide Page 129
- Page / 145
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting AP-800 User Guide
Recovery Procedures
129
Bootloader=> set netmask 255.255.255.0
Bootloader=> set ipaddrtype static
Bootloader=> show
Bootloader=> reboot
The AP will reboot and then download the image file. You should see downloading activity begins after a few seconds
within the TFTP server’s status screen.
8. When the download process is complete, configure the AP.
Setting IP Address using Serial Port
Use the following procedure to set an IP address over the serial port using the CLI. The network administrator typically
provides the AP IP address.
Hardware and Software Requirements
• Standard cross-over serial data (RS-232) cable (not included with shipment).
• ASCII Terminal software, such as HyperTerminal.
Attaching the Serial Port Cable
1. Connect one end of the serial cable to the AP and the other end to a serial port on your computer.
2. Power on the computer and AP, if necessary.
Initializing the IP Address using CLI
After installing the serial port cable, you may use the CLI to communicate with the AP. CLI supports most generic terminal
emulation programs, such as HyperTerminal (which is included with the Windows operating systems). In addition, many
web sites offer shareware or commercial terminal programs you can download. Once the IP address has been assigned,
you can use the HTTP interface or the CLI over Telnet to complete configuration.
Follow these steps to assign the AP an IP address:
1. Open your terminal emulation program (like HyperTerminal) and set the following connection properties:
• Com Port: <COM1, COM2, etc., depending on your computer>
• Baud rate: 115200
•Data Bits: 8
• Stop bits: 1
• Flow Control: None
• Parity: None
2. Under File > Properties > Settings > ASCII Setup, enable the Send line ends with line feeds option.
HyperTerminal sends a line return at the end of each line of code.
3. Press the RESET button on the AP.
The terminal display shows Power On Self Tests (POST) activity, and then displays a CLI prompt, similar to the
example below. This process may take up to 90 seconds.
Bootloader=> Please enter password:
4. Enter the CLI password (default is public).
The terminal displays a welcome message and then the CLI Prompt:
Bootloader=>
5. Enter show ip. Network parameters appear:
- ORiNOCO AP-800 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- AP-800 User Guide 7
- Introduction 8
- Core Features of AP-800 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 17
- Installing the Software 20
- Update Device 21
- Retrieve From Device 23
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Filtering 72
- Management Access Control 86
- System Log 88
- Event Log 90
- Pre-requisites 99
- Viewing the MIB Objects 99
- Configuring the MIB Objects 100
- Global Configuration Mode 101
- General Notes 101
- Log into the AP using Telnet 104
- User Exec Mode 104
- Privileged Exec Mode 105
- Show QoS EDCA Command 109
- Wireless VAP Command 110
- System Information Command 115
- Event Logand ICMP Commands 116
- RADIUS Client Access Command 118
- Interface Statistics Command 118
- Filter-status 119
- Protocol-name 119
- Protocol-number 119
- Again entry-status 119
- Troubleshooting 121
- Symptoms and Solutions 122
- Client Connection Problems 124
- VLAN Operation Issues 124
- Gigabit Ethernet PoE 125
- Recovery Procedures 126
- Related Applications 130
- ASCII Character Chart 131
- Bootloader CLI 132
- Specifications 134
- Advanced Bridging Functions 135
- Security Features 135
- Hardware Specifications 136
- Available Channels 137
- Support Options 142
- Statement of Warranty 144
- Other Information 145
Related products and manuals for Networking Proxim ORiNOCO
Networking Proxim ORiNOCO Installation Guide
(35 pages)
(35 pages)
Networking Proxim ORiNOCO AP-8000 User's Guide
(169 pages)
(169 pages)
Networking Proxim RangeLAN2 7921 User's Guide
(103 pages)
(103 pages)
Networking Proxim ORiNOCO AP-2500 User's Guide
(251 pages)
(251 pages)
Networking Proxim AP-2000 User's Guide
(244 pages)
(244 pages)
Networking Proxim RangeLAN2 7500 User Manual
(141 pages)
(141 pages)
Networking Proxim 7910 User's Guide
(127 pages)
(127 pages)
(9 pages)© 2020, manymanuals.com. All rights reserved. | 1.313 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals