Proxim ORiNOCO User's Guide Page 15
- Page / 145
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Initialization AP-800 User Guide
Hardware Installation
15
Cabling with Gigabit Ethernet PoE
1. To power the device using Gigabit Ethernet PoE, you must use Gigabit PoE injector (ordered separately). Connect
one end of a CAT6 Ethernet cable (not supplied) to the unit’s LAN port. Connect the other end to the Data and Power
Out port of the PoE Injector.
2. Connect one end of the second CAT6 Ethernet cable to the Data In port of the DC Injector. The other end of the cable
should not be connected to another device until installation is complete:
• Use a straight-through cable if you intend to connect the unit to a switch, hub or patch panel.
• Use a cross-over Ethernet cable (CAT6) or adapter if you intend to connect the unit to a single computer.
Using a Console Port
You may connect your Access Point with a console port. Follow the steps provided below if you are using the Console
port:
1. Connect a nine-pin, male-to-female serial cable to the COM port on a computer or laptop and to the DB9 connector of
the Access Point.
2. Open the Microsoft’s HyperTerminal to set up the AP-800. For more information refer Initialization.
Install the Cable Security Cover (Optional)
When the RS-232 cable is not connected, you may install a security cover to deter unauthorized access to the unit. The
security cover is a plastic enclosure that prevents access to the power and LAN ports, and the Reset and Reload
buttons.
1. Open the split end of the security cover just enough to slide the power cable (if you are not using Gigabit Ethernet
PoE) and the CAT 6 Ethernet cable through the opening until they fit inside the straight clamping portion of the cover.
Exercise care as you slide the cable (s) so you do not accidentally break the cover.
2. Slide the hinging end of the security cover into the hole on the rear panel of the unit to the left of connectors. Once in
place, pivot the cover to bring it close to the rear panel of the unit.
3. Use two screws to fasten the security cover on to the rear panel of the unit.
Install the Antenna
The omni-directional antennas supplied with the product do not require any professional installation as they have
non-standard connectors.
NOTE: Optionally, you can use the Range extended Antenna (REA). This accessory also has non-standard connectors,
and can install them easily.
If the regular outdoor antennas are used, connected via a pigtail conversion cable that offers a standard connector type
for antenna connection, then professional installation is required.
Follow these steps to assemble the antennas to AP-800:
1. Hand-tighten the antennas clockwise, onto the outer connectors of AP-800 until they are firmly attached.
2. Position the antennas as close to the horizontal surface (ceiling or wall), so as to get the maximum signal coverage of
the omni-directional antenna.
NOTE: Proxim recommends to aim the antenna horizontal, as the wireless coverage angle is wider with the antenna
pointing up or down.
Mount the Unit
Proxim recommends that you have site survey professionally conducted to determine the best location for the AP.
The following considerations must be kept in mind when the AP-800 is mounted.
- ORiNOCO AP-800 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- AP-800 User Guide 7
- Introduction 8
- Core Features of AP-800 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 17
- Installing the Software 20
- Update Device 21
- Retrieve From Device 23
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Filtering 72
- Management Access Control 86
- System Log 88
- Event Log 90
- Pre-requisites 99
- Viewing the MIB Objects 99
- Configuring the MIB Objects 100
- Global Configuration Mode 101
- General Notes 101
- Log into the AP using Telnet 104
- User Exec Mode 104
- Privileged Exec Mode 105
- Show QoS EDCA Command 109
- Wireless VAP Command 110
- System Information Command 115
- Event Logand ICMP Commands 116
- RADIUS Client Access Command 118
- Interface Statistics Command 118
- Filter-status 119
- Protocol-name 119
- Protocol-number 119
- Again entry-status 119
- Troubleshooting 121
- Symptoms and Solutions 122
- Client Connection Problems 124
- VLAN Operation Issues 124
- Gigabit Ethernet PoE 125
- Recovery Procedures 126
- Related Applications 130
- ASCII Character Chart 131
- Bootloader CLI 132
- Specifications 134
- Advanced Bridging Functions 135
- Security Features 135
- Hardware Specifications 136
- Available Channels 137
- Support Options 142
- Statement of Warranty 144
- Other Information 145
Related products and manuals for Networking Proxim ORiNOCO
Networking Proxim ORiNOCO Installation Guide
(35 pages)
(35 pages)
Networking Proxim ORiNOCO AP-8000 User's Guide
(169 pages)
(169 pages)
Networking Proxim RangeLAN2 7921 User's Guide
(103 pages)
(103 pages)
Networking Proxim ORiNOCO AP-2500 User's Guide
(251 pages)
(251 pages)
Networking Proxim AP-2000 User's Guide
(244 pages)
(244 pages)
Networking Proxim RangeLAN2 7500 User Manual
(141 pages)
(141 pages)
Networking Proxim 7910 User's Guide
(127 pages)
(127 pages)
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.977 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals