Proxim ORiNOCO User's Guide Page 17
- Page / 145
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Initialization AP-800 User Guide
Initialization
17
• RED: 100 Mbps
• BLANK: No link available or Ethernet is not connected
NOTE: When in operational status, the wireless LEDs will be steady Green. The wireless LEDs would blink Green when
the wireless traffic is being transmitted or received.
Initialization
The following sections detail how to initialize the AP using the ScanTool, log in to the HTTP interface, perform an initial
configuration if required (the Access Points are configured to a default settings) and download the required AP software.
Using ScanTool
ScanTool is a software utility that is included in the installation CD-ROM. It is an initial configuration tool that allows you to
find the IP address of an Access Point by referencing the MAC address in a Scan List, or to assign an IP address if one
has not been assigned.
The tool automatically detects the Access Points installed in your network, regardless of IP address, and lets you
configure each unit’s IP settings. In addition, you can use set initial device parameters that will allows the AP to retrieve
new software to an AP that does not have a valid software image installed.
To access the HTTP interface and configure the AP, the AP must be assigned an IP address that is valid on its Ethernet
network. By default, the AP is configured to obtain an IP address automatically from the network Dynamic Host
Configuration Protocol (DHCP) server during the boot-up.
If your network contains a DHCP server, you can run the ScanTool to find out what IP address the AP has been assigned.
If your network does not contain a DHCP server, the Access Point’s IP address defaults to 169.254.128.132 and the
device starts with a dynamic IP address. By default, the IP address is Static.
ScanTool Instructions
Follow these steps to install ScanTool and initialize the AP:
1. Power up, reboot, or reset the AP.
2. Double-click the ScanTool icon on the Windows desktop to launch the program (if the program is not already running).
If the icon is not on your desktop, click Start > All Programs > ORiNOCO > AP-800 > Xtras > ScanTool.
NOTE: If your computer has more than one network adapter installed, you will be prompted to select the adapter that
you want ScanTool to use before the Scan List appears. You can use either an Ethernet or wireless adaptor. If
prompted, select an adapter and click OK. You can change your adapter setting at any time by clicking the Select
Adapter button on the Scan List screen.
ScanTool scans the subnet and displays all detected Access Points. The ScanTool’s Scan List screen appears, as shown
Figure 2-4 ScanTool
- ORiNOCO AP-800 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- AP-800 User Guide 7
- Introduction 8
- Core Features of AP-800 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 17
- Installing the Software 20
- Update Device 21
- Retrieve From Device 23
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Filtering 72
- Management Access Control 86
- System Log 88
- Event Log 90
- Pre-requisites 99
- Viewing the MIB Objects 99
- Configuring the MIB Objects 100
- Global Configuration Mode 101
- General Notes 101
- Log into the AP using Telnet 104
- User Exec Mode 104
- Privileged Exec Mode 105
- Show QoS EDCA Command 109
- Wireless VAP Command 110
- System Information Command 115
- Event Logand ICMP Commands 116
- RADIUS Client Access Command 118
- Interface Statistics Command 118
- Filter-status 119
- Protocol-name 119
- Protocol-number 119
- Again entry-status 119
- Troubleshooting 121
- Symptoms and Solutions 122
- Client Connection Problems 124
- VLAN Operation Issues 124
- Gigabit Ethernet PoE 125
- Recovery Procedures 126
- Related Applications 130
- ASCII Character Chart 131
- Bootloader CLI 132
- Specifications 134
- Advanced Bridging Functions 135
- Security Features 135
- Hardware Specifications 136
- Available Channels 137
- Support Options 142
- Statement of Warranty 144
- Other Information 145
Related products and manuals for Networking Proxim ORiNOCO
Networking Proxim ORiNOCO Installation Guide
(35 pages)
(35 pages)
Networking Proxim ORiNOCO AP-8000 User's Guide
(169 pages)
(169 pages)
Networking Proxim RangeLAN2 7921 User's Guide
(103 pages)
(103 pages)
Networking Proxim ORiNOCO AP-2500 User's Guide
(251 pages)
(251 pages)
Networking Proxim AP-2000 User's Guide
(244 pages)
(244 pages)
Networking Proxim RangeLAN2 7500 User Manual
(141 pages)
(141 pages)
Networking Proxim 7910 User's Guide
(127 pages)
(127 pages)
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.403 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals