Proxim ORiNOCO User's Guide Page 52
- Page / 145
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Access Point Features AP-800 User Guide
Monitoring the Device
52
AP fails to retrieve the information after three attempts, the AP will use the system uptime and update the relevant time
objects. If this feature is disabled, the user cannot configure the date and time parameters.
SNTP Features
• SNTP Status: This parameter is used to enable or disable the SNTP functionality.
• Primary Server Name Or IP Address: This parameter is used for the primary SNTP server IP address name.
• Secondary Server Name Or IPAddress: This parameter is used for the secondary SNTP server IP address name.
• Time Zone: This parameter is used to specify the appropriate time zone.
Day Light Saving Time: This parameter is used to indicate the number of hours to adjust for Daylight Saving Time.
Interface Statistics
Statistics feature provides you the information about the various interfaces that are available for the Access Points. The
sub-features that are available are described below:
Station Statistics
Station Statistics display information on wireless clients attached to the AP.
• VAP Number: The VAP number on which the client is connected with the AP.
• MAC Address: The MAC address of the wireless client for which the statistics are gathered.
• Rx Data Frames: The number of data frames that are received.
• Tx Data Frames: The number of data frames that are transmitted.
• RSSI: This represents the Received Signal Strength of the Station.
• Tx Rate: This parameter represents the transmission rate of the station.
• State: This parameter represents the present status of the station.
Wireless Statistics
Wireless Statistics display information on the wireless interface.
• Description: Information about the interface (e.g., the name of the manufacturer, the product name and the version of
the hardware interface).
• Type: This displays the type of interface.
• MTU: Maximum Transfer Unit is the largest size of IP datagram which may be transferred using a speciifc data link
connection. The size of MTU may vary greatly between different links.
• Physical Address: The wireless interface’s address at the protocol layer immediately below the network layer in the
protocol stack.
• Operational Status: The current state of the interface: Up (ready to pass packets), Down (not ready to pass packets,
or Testing (testing and unable to pass packets).
• Last Change: The value of the sysUpTime object at the time the interface entered its current operational state.
• In Octets: The total number of octets received on the interface, including framing characters.
• In Ucast Packets: The number of subnetwork unicast packets delivered to a higher-layer protocol.
• In Nucast Packets: The number of non-unicast (i.e., subnetwork-broadcast or subnetwork-multicast) packets
delivered to a higher-layer protocol.
• In Errors: The number of inbound packets that contained errors preventing them from being deliverable to a
higher-layer protocol.
• Out Octets (bytes): The total number of octets transmitted out of the interface, including framing characters.
• Out Ucast Packets: The total number of packets that higher-level protocols requested to be transmitted to a
subnetwork-unicast address, including those that were discarded or not sent.
- ORiNOCO AP-800 1
- Copyright 2
- Trademarks 2
- GPL License Note 2
- OpenSSL License Note 2
- AP-800 User Guide 7
- Introduction 8
- Core Features of AP-800 9
- Hardware Overview 10
- Prerequisites 12
- System Requirements 13
- Product Package 13
- Optional Accessories 14
- Hardware Installation 14
- Using a Console Port 15
- Install the Antenna 15
- Mount the Unit 15
- Power on the Unit 16
- Initialization 17
- Installing the Software 20
- Update Device 21
- Retrieve From Device 23
- Managing the Access Point 27
- SNMP Management 28
- SSH (Secure Shell) Management 28
- HyperTerminal 28
- ProximVision ES 29
- Password Management 31
- Access Point Features 34
- Ethernet 36
- Security 36
- IP Configuration 43
- TPID Priority CFI VID 45
- Managing the Device 48
- Upgrading the Firmware 49
- Monitoring the Device 51
- Interface Statistics 52
- Network Layer 54
- Web Interface Overview 56
- Error Message 56
- Configuring the Device 57
- Filtering 72
- Management Access Control 86
- System Log 88
- Event Log 90
- Pre-requisites 99
- Viewing the MIB Objects 99
- Configuring the MIB Objects 100
- Global Configuration Mode 101
- General Notes 101
- Log into the AP using Telnet 104
- User Exec Mode 104
- Privileged Exec Mode 105
- Show QoS EDCA Command 109
- Wireless VAP Command 110
- System Information Command 115
- Event Logand ICMP Commands 116
- RADIUS Client Access Command 118
- Interface Statistics Command 118
- Filter-status 119
- Protocol-name 119
- Protocol-number 119
- Again entry-status 119
- Troubleshooting 121
- Symptoms and Solutions 122
- Client Connection Problems 124
- VLAN Operation Issues 124
- Gigabit Ethernet PoE 125
- Recovery Procedures 126
- Related Applications 130
- ASCII Character Chart 131
- Bootloader CLI 132
- Specifications 134
- Advanced Bridging Functions 135
- Security Features 135
- Hardware Specifications 136
- Available Channels 137
- Support Options 142
- Statement of Warranty 144
- Other Information 145
Related products and manuals for Networking Proxim ORiNOCO
Networking Proxim ORiNOCO Installation Guide
(35 pages)
(35 pages)
Networking Proxim ORiNOCO AP-8000 User's Guide
(169 pages)
(169 pages)
Networking Proxim RangeLAN2 7921 User's Guide
(103 pages)
(103 pages)
Networking Proxim ORiNOCO AP-2500 User's Guide
(251 pages)
(251 pages)
Networking Proxim AP-2000 User's Guide
(244 pages)
(244 pages)
Networking Proxim RangeLAN2 7500 User Manual
(141 pages)
(141 pages)
Networking Proxim 7910 User's Guide
(127 pages)
(127 pages)
(9 pages)© 2020, manymanuals.com. All rights reserved. | 1.439 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals